View PPM20-D-05E_755974.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www.make-ps.com
E-mail:info@make-ps.com
Single Output AC/DC Converter
Series PPM
5-25 Watt | AC-DC Converter
Input Specifications
Input voltage range Input frequency Input current PPM05 PPM10 PPM15 PPM20 PPM25 Inrush current PPM05 PPM10 PPM15 PPM20/PPM25 PPM05 PPM10/PPM15 PPM20/PPM25 85- 264VAC, 120- 370VDC 47- 63Hz 110VAC 230VAC 120mA , typ. 70mA , typ. 230mA , typ. 120mA , typ. 250mA , typ. 140mA , typ. 330mA , typ. 180mA , typ. 420mA , typ. 230mA , typ. 110VAC 230VAC 10A, typ. 20A, typ. 10A, typ. 20A, typ. 10A, typ. 20A, typ. 16A, typ. 30A, typ. 1A/250V slow blow 2A/250V slow blow 3.15A/250V slow blow 2%(main out) 0.5% (main output) 1.5% (supplement output) 1% 100mV Continuous, and auto resume 110% IO 6.5VDC 12VDC 20VDC 30VDC 60VDC
External input fuse(recommended)
Output Specifications
Voltage set accuracy Input variation Load variation (10-100%) Single output models Ripple& noise(p-p) 20MHz Bandwidth Short circuit protection Over current protection Over output voltage protection 3.3 / 5VDC models 9VDC model 12 / 15VDC models 24VDC model 48VDC model
General Specifications
Temperature ranges Operating : Power derating above 55 C: Storage: Case temperature: PPM05, PPM10, PPM15, PPM20/25 (Vin=230VAC) -25 to +70 C C 3.75%/ (2.25%/C PPM20-D-05ELF < 50) C -25 to +105 C C +90 max C ~50g, ~70g, ~80g, ~120g 80ms(typ.) 85%(max) 0.02% / C 150kHz max See table 3000VAC/1Min 0.3mA RMS typ. 230VAC/50Hz UL 94V-0 rated PCB >200,000h @25 C Soldering 260 / max. 10 sec. C
Weight Hold-up time Humidity (non condensing) Temperature coefficient Switching frequency Efficiency I/O-isolation voltage Leakage current Case material Install MTBF RoHS compliant
1/4
www.make-ps.com
Examples of Partnumbers/Modelcode
PART NO. Power (Watt) INPUT CURRENT (mA, typ..) 110VAC / 230VAC OUTPUT (Volt)
E-mail:info@make-ps.com
RIPPLE AND NOISE (typ..) EFFICIENCY (% min.)
PPM05-A-3.3E 4 120 / 70 PPM05-A-05E 5 120 / 70 PPM05-A-09E 5 120 / 70 PPM05-A-12E 5 120 / 70 PPM05-A-15E 5 120 / 70 PPM05-A-24E 5 120 / 70 PPM10-B-3.3E 6.6 230 / 120 PPM10-B-05E 10 230 / 120 PPM10-B-09E 10 230 / 120 PPM10-B-12E 10 230 / 120 PPM10-B-15E 10 230 / 120 PPM10-B-24E 10 230 / 120 PPM15-C-3.3E 9.9 250 / 140 PPM15-C-05E 15 250 / 140 PPM15-C-09E 15 250 / 140 PPM15-C-12E 15 250 / 140 PPM15-C-15E 15 250 / 140 PPM15-C-24E 15 250 / 140 PPM15-C-48E 15 250 / 140 PPM20-D-3.3E 20 330 / 180 PPM20-D-05E 20 330 / 180 PPM20-D-12E 20 330 / 180 PPM20-D-15E 20 330 / 180 PPM20-D-24E 20 330 / 180 PPM25-D-05E 25 420 / 230 PPM25-D-12E 25 420 / 230 PPM25-D-15E 25 420 / 230 PPM25-D-24E 25 420 / 230 PPM25-D-48E 25 420 / 230 Other specifications please enquire.
3.3V / 1250mA 5V / 1000mA 9V / 550mA 12V / 420mA 15V / 330mA 24V / 230mA 3.3V / 2000mA 5V / 2000mA 9V / 1100mA 12V / 900mA 15V / 700mA 24V / 450mA 3.3V / 3000mA 5V / 2800mA 9V / 1600mA 12V / 1250mA 15V / 1000mA 24V / 625mA 48V / 320mA 3.3V / 4100mA 5V / 3500mA 12V / 1600mA 15V / 1300mA 24V / 850mA 5V / 4100mA 12V / 2100mA 15V / 1600mA 24V / 1100mA 48V / 500mA
50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV 50mV
70 75 77 79 80 82 70 76 78 80 81 82 73 76 78 80 80 84 85 73 75 81 83 85 74 82 83 85 87
2/4
www.make-ps.com
Dimensions / Pinning
E-mail:info@make-ps.com
PINNING PPMxx-x-xxE # Single Output 1 2 3 4 5 6 7 8 TRIM Ground* AC (N) AC (L) - V Output Omitted Omitted Omitted + V Output TRIM**
NOTE: ** Only for PPM20/25-x Unit: mm Pin section: 1.00mm Pin tolerances: +/- 0.1mm General tolerances: +/- 0.5mm
No. PPMxx-A A 12.5 B 48.5 C 40.5 D 4.0 E 16.0 F 36.0 G 20.5 H min. 6.0 No. A B C D E F G H PPMxx-B 17.5 55.0 47.0 5.0 20.0 45.0 20.5 min. 6.0 No. A B C D E F G H PPMxx-C 17.5 62.0 54.0 5.0 20.0 45.0 22.5 min. 6.0 No. A B C D E F G H PPMxx-D 20.0 70.0 62.0 5.75 23.0 48.0 23.5 min. 6.0
* No G. on PPM15-x
App Notes
Remarks : 1.Ripple and Noise were measured by the method of parallel lines; 2.Unless otherwise specified, all specifications above are measured at rated input voltage and rated output load, TA=25 humidity < 75%; C, 3.All specifications stated in this datasheet are subject to the above listed model only. For specifications of non-standard model, please contact our technical support team.
3/4
www.make-ps.com
Parallel Lines Measure
E-mail:info@make-ps.com
Copper sheet
Fuse C1 C2 Connect Oscillograph Probe
Load
2 25.4m m 25.4m m
Typical Applications PPM-Series
PPMxx-x-xxELF (single Output)
L N FG
Fuse NT C
L N
FG
-Vo +Vo
C1 C2 Tvs 1 RL
Remarks 1.Output filtering capacitor C5, C3 and C1 are electrolytic capacitor. It is recommended to use high frequency and low resistance electrolytic capacitor. For capacitance and current of the capacitor please refer to suppliers' specifications. Voltage derating of capacitor should be 80% or above.C2, C4 and C6 eliminate high frequency noise. TVS is a recommended component to protect postcircuits (when converter fails). 2. External input NTC is recommended to use 5D-9 (Only PPM10 model and PPM15 model)
Partnumber PPM05-A-3.3E PPM05-A-05E PPM05-A-09E PPM05-A-12E PPM05-A-15E PPM05-A-24E PPM10-B-3.3E PPM10-B-05E PPM10-B-09E PPM10-B-12E PPM10-B-15E PPM10-B-24E
External Typical Value C1 Partnumber 330 PPM15-C-3.3E 330 PPM15-C-05E 120 PPM15-C-09E 120 PPM15-C-12E 68 PPM15-C-15E 68 PPM15-C-24E PPM15-C-48E 470 330 PPM20-D-3.3E 120 PPM20-D-05E 120 PPM20-D-12E 120 PPM20-D-15E 68 PPM20-D-24E PPM25-D-12E PPM25-D-15E PPM25-D-24E PPM25-D-48E
C1 680 680 470 220 220 68 33 330 330 220 220 220 330 330 120 68
TRIM (only PPM20/25-D-xxE
R1(K ) R2(K ) R3(K ) Vref(V) Vot(V)
3.3V 2 1.2 1 1.24
5V 3.3 3.3 1 2.5
12V 3.83 1 1 2.5
15V 7.5 1.5 1 2.5
24V 8.66 1 1 2.5
48V 1.2 22 1.2 2.5
Output voltage of Trim, variation 10%
Note: Value for R1, R2, R3, and Vref refer to the following table. RT: Resistance of Trim a: User-defined parameter, no actual meanings.
4/4

▲Up To Search▲

Price & Availability of PPM20-D-05E

	To Download PPM20-D-05E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .